成人影视久久一区丝袜美腿,色情免费100部A片看片,国产精品久久久久久久久99热,69久久夜色精品国产69蝌蚪网,翁公吮她的花蒂及奶水风紫阳,九色丨熟女丨高潮,玩弄美艳馊子小说短篇,插的太爽好丰满

RTP600W厚膜無感電阻10Ω100Ω200Ω300Ω500Ω1MΩ
RTP600W厚膜無感電阻10Ω100Ω200Ω300Ω500Ω1MΩ
產品價格:¥10(人民幣)
  • 規格:RTP600
  • 發貨地:本地至全國
  • 品牌:
  • 最小起訂量:1只
  • 誠信商家
    會員級別:鉆石會員
    認證類型:企業認證
    企業證件:通過認證

    商鋪名稱:深圳市華鑫歐電子有限公司

    聯系人:吳偉(先生)

    聯系手機:

    固定電話:

    企業郵箱:szhxwuwei2008@163.com

    聯系地址:深圳市寶安區石巖鎮洲石路石頭山工業區2號廠房3樓

    郵編:518108

    聯系我時,請說是在五金機電網上看到的,謝謝!

    商品詳情

      RTP600


      功率型 厚膜 無感 電阻器     Power type   Thick film     Non inductive Resistor


      l  底板中心溫度≤85℃ 額定功率 250W~800W


      l  Base plate center temperature ≤ 85℃ Rated power 250W~800W.


      l  特殊設計的外型結構,芯片和外殼之間用彈簧聯接,用兩個螺絲固定安裝,能保證散熱片附著壓力在 120 到 160 牛頓之間。


      l  The specially designed structural shape connects the chip and the casing with springs and is securely mounted with two screws, ensuring that the pressure of the heatsink attachment is between 120 and 160 Newtons.


      l  搭配合適的散熱器使用時,功率可達到 2000W


      l  When used with a suitable radiator, the power can reach 2000W


      主要應用于變速驅動器、供電、 控制設備、通訊、自動控制、發動機控制等。適合逆變器電路、脈沖電路、高頻電路。

      Mainly used in variable speed drives, power supply, control equipment, communication, automatic control, engine control, etc. Suitable for inverter circuits, pulse circuits, and high-frequency circuits.


      降功率曲線斜率(熱阻):RTP600:8.57W/K(0.12K/W)


      額定功率

      阻值范圍

      阻值允許偏差

      電阻溫度系數

      最大工作電壓

      耐電壓

      Rated

      Resistance

      Resistance

      Temperature coefficient

      Maximum working

      Withstanding

      power

      range

      Tolerance

      (PPM/℃)

      voltage

      voltage

      600W

      0.5Ω-1MΩ

      ±1%、±5% 、±10%

      ±150

      5000VDC

      6KV/Min


      ©2025 V1.0


      RTP600


      功率型 厚膜 無感 電阻器     Power type   Thick film     Non inductive Resistor

      試驗項目

      試驗條件

      性能指標

      Test items

      Experimental conditions

      Performance indicators

      溫度快速變化

      -55℃~+155℃,經五次循環;極限溫度暴露時間:

      電阻器應無可見損傷且標志清楚

      30 分鐘;轉換時間:1~2 分鐘

      The resistor should have no visible

      Rapid temperature

      -55 ℃ to+155 ℃, after five cycles; Extreme temperature

      damage and clear markings,

      changes

      exposure time: 30 minutes; Conversion time: 1-2 minutes

      △R≤±(0.5%R+0.05Ω)

      溫度系數

      TCR 在±150X10-6/K 之內

      Temperature

      25℃~105℃

      TCR within ± 150X10-6/K

      coefficient

      正常氣候條件下,在電阻器的金屬散熱板與引出端之間

      測試絕緣電阻,試驗電壓(直流)為 500±5V

      絕緣電阻應≥10GΩ

      絕緣電阻

      Under normal weather conditions, test the insulation

      The insulation resistance should be

      Insulation resistance

      resistance between the metal heat dissipation plate of the

      ≥10GΩ

      resistor and the lead out terminal, with a test voltage (DC)

      of 500 ± 5V

      施加額定功率 2 倍的直流電壓(Us≤1.5Umax)

      電阻器應無可見損傷且標志清楚

      過載

      時間為5秒

      The resistor should have no visible

      Overload

      Apply a DC voltage of twice the rated power

      damage and clear markings,

      (Us ≤ 1.5 Umax) for 5 seconds

      △R≤±(0.5%R+0.05Ω)

      穩態濕熱

      電阻器應無可見損傷且標志清楚

      溫度:40±2℃;濕度 95%;時間:56 天

      The resistor should have no visible

      Damp heat steady

      Temperature: 40 ± 2 ℃; Humidity of 95%; Time: 56 days

      damage and clear markings,

      state

      △R≤±(0.5%R+0.05Ω)

      施加電壓:額定功率直流電壓(UR≤U max)

      電阻器應無可見損傷且標志清楚

      壽命

      1.5 小時通電,0.5 小時斷電,總時長 1000 小時

      The resistor should have no visible

      Life

      Applied voltage: rated power DC voltage (UR ≤ U max),

      damage and clear markings,

      powered on for 1.5 hours, powered off for 0.5 hours, total

      △R≤±(0.5%R+0.05Ω)

      duration 1000 hours

      電阻器無擊穿或飛弧現象,漏電流

      耐電壓

      施加交流有效值電壓 6KV,時間為 1 分鐘±5 秒

      ≤10mA

      Withstanding

      Apply an effective AC voltage of 6KV for 1 minute ± 5

      The resistor has no breakdown or

      voltage

      seconds

      arcing phenomenon, and the

      leakage current is ≤ 10mA

      按 GB/T2423.10-2019 要求進行試驗,振動頻率為

      10Hz,振幅 0.35mm,加速度 50m/s2,每個方向 2 次掃頻,

      電阻器塑封體應無機械損傷,阻值

      振動

      3 個方向,每個方向持續時間 23 分鐘

      變化在±2%R+0.05Ω之內

      Vibrate

      Conduct the test according to the requirements of

      The plastic casing of the resistor

      GB/T2423.10-2019, with a vibration frequency of 10Hz,

      should have no mechanical

      amplitude of 0.35mm, acceleration of 50m/s 2, 2 frequency

      damage, and the resistance change

      scans in each direction, 3 directions, and a duration of 23

      should be within ± 2% R+0.05 Ω

      minutes in each direction

      ©2025 V1.0


      RTP600

      功率型 厚膜 無感 電阻器     Power type   Thick film    Non inductive Resistor


      產品類型

      功率

      阻值

      精度

      Product type

      Power

      Resistance

      Accuracy

      3R9=3.9Ω

      F:±1%

      RTP

      600 Watts

      10R=10Ω

      J: ±5%

      20K=20KΩ

      K: ±10%


      l  電阻器通過螺絲安裝在散熱器上,螺絲安裝扭矩為 2N.m,應確保產品安裝緊固,無晃動。另外應為螺絲配套防松組件,如:平墊、彈墊、防松螺母等。


      l  The resistor is installed on the heat sink with screws, and the installation torque of the screws is 2N. m. It should be ensured that the product is installed firmly without shaking. In addition, screws should be equipped with anti loosening components such as flat washers, spring washers, anti loosening nuts, etc.


      l  電阻器引出端電氣安裝使用的是 M5 螺絲,螺絲安裝扭矩為 1.3N.m,應確保電氣連接緊固,無晃動。另外應為螺絲配套防松組件,如:平墊、彈墊等,防止振動造成電氣連接松脫。


      l  M5 screws are used for the electrical installation of the resistor lead out end, with a torque of 1.3N. m. It should be ensured that the electrical connection is tight and there is no shaking. In addition, screws should be equipped with anti loosening components, such as flat washers, spring washers, etc., to prevent electrical connections from loosening due to vibration.


      l  電阻器與安裝面之間需要均勻的涂覆一層導熱硅脂,推薦使用導熱系數 1W/mK 的導熱硅脂產品。


      l  A uniform layer of thermal grease should be applied between the resistor and the installation surface. It is recommended to use thermal grease products with a thermal conductivity of 1W/mK.


      l  產品在貯存期間,應貯存在環境溫度為-10℃~+45℃,相對濕度不大于 85% ,通風、干燥、周圍無酸堿或其他有害物質的倉庫內。


      l  During storage, the product should be stored in a warehouse with an ambient temperature of -10 ℃ to+45 ℃, a relative humidity of no more than 85%, ventilation, dryness, and no acidic, alkaline, or other harmful substances around it


      ©2025 V1.0

    0571-87774297